نظام طلاء قابل للتخصيص لتصنيع المنتجات الخرسانية

Ⅰ.Product Overview

Different concrete products require different mold configurations and spraying arrangements. Mold dimensions, production-line speed, and release-agent properties all influence how the spraying system should be configured.

The QGM Coating System is a customizable, low-pressure spraying solution designed to apply mold release agents in concrete product manufacturing. It can be configured for applications involving concrete blocks, paving stones, wall panels, and AAC blocks.

The system combines coaxial atomization with controlled release-agent delivery. Spray pressure, flow rate, nozzle quantity, spacing, and arrangement can be selected according to the intended application.

The spray beam and nozzle layout can also be engineered to accommodate different product dimensions and mold widths. This configuration-based approach allows the system to be evaluated for different production-line requirements.

A suitable configuration should be established from actual mold drawings, product dimensions, line-speed requirements, and release-agent specifications rather than relying on a generic arrangement.

Ⅱ. Technical Specifications

Ⅲ.Technical Advantages

1. Spray Beam and Nozzle Arrangement

The spray beam, nozzle quantity, nozzle spacing, and nozzle arrangement can be customized according to mold width, product dimensions, and the required spray coverage.

This allows the spraying layout to be designed around the application area instead of using an identical arrangement for every concrete product.

2. Low-Pressure Spraying and Flow Control

The system uses low-pressure spraying to apply release agent to the mold surface. Material flow and spray pressure can be controlled to help limit excessive application.

According to the supplied product information, the system can reduce release-agent consumption by up to approximately 70% compared with conventional application methods. Actual consumption depends on the existing process and operating conditions.

3. Coaxial Atomization

Release agent and atomizing air travel through separate channels and mix at the nozzle outlet.

This arrangement supports the atomization and distribution of release agent onto the target mold surface. The nozzle layout and spray height should be selected according to mold geometry and coverage requirements.

4. Rapid Valve Response and Independent Nozzle Control

Control valves enable rapid spray activation and shutoff. Independent nozzle control allows individual spraying points to be managed separately.

These functions help reduce dripping and unnecessary spraying while supporting the application requirements of automated concrete manufacturing processes.

5. Adaptation to Different Production-Line Speeds

Production-line speed is one of the factors considered when configuring the system. The spraying arrangement can be engineered according to the intended operating speed and mold dimensions.

The actual configuration should be confirmed through technical evaluation of the production process and required spray coverage.

6. Support for Mold Protection and Workplace Cleanliness

Controlled release-agent application helps reduce excessive spraying and oil-mist dispersion. A uniform coating also helps reduce demolding resistance and the risk of mold-surface wear and corrosion.

Suitable release-agent properties and spraying parameters should be selected for the specific mold material and operating environment.

Ⅳ.Applications

The QGM Coating System can be configured for release-agent application in production processes involving:

Concrete Blocks

The nozzle arrangement can be selected according to the dimensions and configuration of the molds used for concrete block production.

Concrete Paving Stones

Spraying parameters and nozzle placement can be evaluated according to the mold geometry and required coverage.

Concrete Wall Panels

The spray beam and nozzle layout can be configured according to the dimensions of the mold and the production process.

AAC Blocks

The spraying arrangement should be assessed according to the specific equipment configuration, mold structure, and release-agent application requirements.

The suitability of a particular arrangement should be confirmed for each application, especially where mold geometry or production conditions differ significantly.

Configure Your Concrete Product Spraying System with QGM

The QGM Coating System combines low-pressure spraying, coaxial atomization, rapid valve response, and configurable nozzle arrangements to support mold release-agent application across different concrete product manufacturing processes.

Its configuration can be evaluated according to the product range, mold geometry, production-line speed, and release-agent properties.

Contact QGM with your product specifications and production-line requirements to discuss a suitable spraying arrangement.

مصنع جديد في منطقة تيلانجانا الصناعية في تشوانتشو

زينيث مصنع آلة GmbH

الخدمات العالمية

خدمات مابعد البيع